Options & Accessories

GRL-USB-PD-C2-QC
– Upgrade GRL-USB-PD-C2 to Qualcomm QuickCharge 4+ (SW Upgrade)

GRL-USB-PD-C2-CTRL – USB Type-C Physical Layer Test Controller (HW and API Only)

GRL-USB-PD-C2-SUP – Upgrades GRL-USB-PD-CTRL to PD3.0 Tester (SW Upgrade)

GRL-USB-PD – GRL USB PD 3.0 Software for Oscilloscopes (SW Only)

GRL-USB-PD-FLT – GRL USB PD 3.0 Software for Oscilloscopes (SW with USB HW License)

GRL-USB-PD-PSB (Coming Soon) – GRL Protocol Sniffer Board (HW Only)

GRL-USB-PD-PTK – GRL Scope Probing and Triggering Kit (HW Only). Package includes BNC to BNC Cable and GRL-C2- EXT4 Probing Board.

GRL-USB-PD-C2-CAB1 – GRL USB PD Cable, Type-C VCONN passthrough (HW Only)

GRL-USB-PD-G2NCB – GRL Gen 2 Noise Calibration Board (HW Only)

GRL-USB-PD-SAB – GRL Serial Interface (SI) Automation Board (HW Only)

GRL-USB-PD-ELDC – External E-Load Connector (HW Only)

Power Supply

USB Cable – Standard Type A to Type B Programming cable used to update GRL-USB-PD-C2 firmware. Connects to GRL-USB-PD-C2 upgrade USB port.

Ethernet Cable – 3m Cat 5 cable to connect GRL-USBPD-C2 test controller to control computer.

GRL-USB-PD-STC – GRL Special (GRL-SPL) Type-C VCONN Passthrough test cable, used for connecting UUT to GRL-USB-PD-C2 test controller. This is a full feature cable with all Type-C lines connected in between both ends of the cable.

Accessory Pouch

GRL-USB-PD-DPC – GRL DPC PHY Tx Automation Test Board, which comprises the following:

  • GRL-C2-EXT1 DisplayPort Fixture, LFPS & FRSWAP Control Board – EXT1 extension fixture for GRL-USB-PD-C2 test controller, used to:
    • Control signals for GRL-C2-FRSWAP AUTO Box Board.
    • Test DisplayPort Alt Mode over Type-C.
    • Control Low Frequency Periodic Signaling (LFPS) sequences in USB 3.0 system.
  • Support for DP PHY automation using GRL-USB-PD-C2 test
    controller.

GRL-USB-PD-FRS – GRL Fast Role Swap (FRSWAP) Board (Coming Soon), which comprises the following:

  • GRL-C2-FRSWAP AUTO Box Board – Fixture for GRL-USBPD-C2 test controller, used to automate Fast Role Swap based testing. Connects to DUT to remove External AC power from DUT.

    Note: The fixture will be shipped inside an enclosure.

  • GRL-C2-EXT5 Extension Board – EXT5 extension fixture for GRL-USB-PD-C2 test controller, used to:

    • Control inputs/outputs from C2.
    • Provide signal triggering for FRSWAP and other peripherals.

GRL-USB-PD-FCB – GRL Type-C Functional Compliance Board (Coming Soon), which comprises the following:

  • GRL-HS-EXT Fixture – Extension fixture for GRL-USB-PD-C2 test controller, used to control VBUS and CC lines between connected devices without interfering the high speed lines between Type-C input/output connectors.
  • Support for functional compliance testing using GRL-USB-PD-C2 test controller.

GRL-USB-PD-TBT – GRL Thunderbolt Power Board (Coming Soon), which comprises the following:

  • GRL-HS-EXT Fixture – Extension fixture for GRL-USB-PD-C2 test controller, used to control VBUS and CC lines between connected devices without interfering the high speed lines between Type-C input/output connectors.
  • GRL-C2-EXT5 Extension Board – EXT5 extension fixture for GRL-USB-PD-C2 test controller, used to:

    • Control inputs/outputs from C2.
    • Provide signal triggering for FRSWAP and other peripherals.
  • GRL-USB-PD-SHT – Extension fixture for GRL-USB-PD-C2 test controller, used to connect to Port 1 and Port 2 of GRL-USB-PDC2 test controller to perform external short circuit for VBUS and VCONN to ground using control signals from GRL-C2-EXT5 extension board.
  • Support for Thunderbolt testing using GRL-USB-PD-C2 test controller.

GRL-USB-PD-STC – GRL Special (GRL-SPL) Type-C VCONN Passthrough test cable, used for connecting UUT to GRL-USB-PD-C2 test controller. This is a full feature cable with all Type-C lines connected in between both ends of the cable.